Light fixtures · Essex, Morris, Union
Light fixture installation and replacement in Essex, Morris and Union County, NJ
Most light fixtures cost $75 to $125 to install (Home Depot); adding one where there was none runs $100 to $650 (HomeGuide). MDL Electric in West Orange installs and replaces light fixtures across Essex, Morris and Union County.
Which job is yours
Swap, heavier fixture, new light or repair: what each job involves in a New Jersey home.
These are the four light fixture jobs this page covers. The first column decides whether the town needs a permit and where the price lands. MDL Electric holds a New Jersey electrical contractor license (34EI01606200) and works from 4 Harrison Avenue in West Orange; call 973.809.2339 and say which job you have.
Scroll sideways to see the whole table.
| The job | What it involves | New Jersey permit | Published cost and time |
|---|---|---|---|
| Swap a fixture for a like or similar one | The same box, wiring and switch. The new fixture's instructions still have to match the wire in the box; see Older homes below. | None. Ordinary maintenance, with no permit or notice to the town (5:23-2.7, 2.14). | $75 to $125 for most fixtures; 1 to 2 hours for a standard fixture (Home Depot). |
| Hang a heavier fixture, such as a chandelier | The box has to carry the weight: up to 50 pounds on a ceiling box, otherwise support of its own or a box listed and marked for more; see Chandeliers and heavy fixtures below. | Ask the town whether it counts as like or similar. A new box or cable is new wiring and needs a permit (5:23-2.14). | Chandelier installed: $220 to $3,400 with the fixture (HomeGuide). |
| Add a light where there is none | A new box fastened to the framing, a new cable and usually a new wall switch. | A permit. In one- and two-family homes, five or fewer new outlets on circuits that can carry the load are minor work, which may start once the town is notified (5:23-2.17A, 2.14). | $100 to $650 to add a light fixture (HomeGuide); up to a full day to run new wiring (Home Depot). |
| Repair a fixture that flickers or stopped working | Find the cause before replacing anything. NFPA lists flickering or dimming lights among the signs to call a qualified electrician. | Replacing a fixture, or part of one, with a like part is ordinary maintenance. New or altered wiring needs a permit. | Electricians charge $50 to $130 an hour, often with a $100 to $200 service call fee (HomeGuide). |
Electrical work in New Jersey is done only by persons licensed to do it, except a single-family homeowner on his or her own home (N.J.A.C. 5:23-2.15). If you are not sure whether your job is a like-for-like swap, your town's building department can tell you.
Older homes
In an older Essex, Morris or Union County house, check the wire before the new fixture goes up.
Most houses in the three counties are older than the wiring that many of today's fixture instructions are written for.
- Many fixtures call for 90°C wire. One maker's instruction sheet reads: "Use power supply wires suitable for at least 90°C (194°F). Note: Most dwellings built before 1985 have supply wire rated to 60°C."AFX fixture instructions
- Family Handyman says the same. A fixture labeled for 90°C wire cannot be safely installed in most houses wired before 1985.Family Handyman
- Most homes here are older than that. Built before 1980: 74.1% of homes in Union County, 72.7% in Essex and 62.1% in Morris, about 531,000 homes in all.US Census ACS 2024 1-year, table B25034
- Many are older still. Built in 1939 or earlier: 30.3% of homes in Essex County, 22.7% in Union and 13.7% in Morris.US Census ACS 2024 1-year, table B25034
- The oldest fixtures may have no box. In knob-and-tube era houses the fixture often hung without one, and an approved box is needed when the fixture is replaced. Old knob-and-tube runs are covered on knob and tube wiring replacement.Family Handyman
- When the cable itself has to go. Replacing old wiring with new wiring of the same capacity is minor work in one- and two-family homes. A whole house is covered on whole-house rewiring, and a check of the whole system on home electrical inspection.N.J.A.C. 5:23-2.17A
Chandeliers and heavy fixtures
What holds a chandelier up: the 50-pound line in the code.
The box in the ceiling carries the fixture, so the weight of the new one decides whether the old box can stay.
- Up to 50 pounds on the box. A ceiling outlet box has to be able to support a fixture weighing up to 50 pounds.IRC E3905.6.2; NEC 314.27(A)(2)
- Heavier than 50 pounds: its own support. A heavier fixture is supported independently of the box, unless the box is listed and marked on the inside for the weight it can carry.IRC E3905.6.2; NEC 314.27(A)(2)
- Wall fixtures up to 6 pounds. A wall fixture that light may be held by other boxes, fastened with at least two No. 6 or larger screws.IRC E3905.6.1
- A high ceiling costs more. HomeGuide puts labor to replace a chandelier at $100 to $150 on a standard ceiling and $200 to $400 on a high one. A new chandelier where there was none runs $150 to $400, or $700 to $2,000 on a high ceiling.HomeGuide, chandelier installation cost
- Allow half a day. HomeGuide puts a chandelier at 2 to 4 hours to install.HomeGuide
Before the old fixture comes down, find the new one's weight on its box or spec sheet. Give MDL the weight and the ceiling height when you call.
Bathrooms and closets
Two rooms where the code limits which light fixture can go where.
From the model residential code and the National Electrical Code, as published by UpCodes, read November 17, 2026.
- Over a tub or shower: no hanging fixtures low. Cord-connected fixtures, chain-, cable- or cord-hung fixtures, lighting track, pendants and ceiling fans with lights cannot have any part within 3 feet horizontally and 8 feet vertically of the tub rim or shower threshold.IRC E4003.11; NEC 410.10(D)
- Over the tub or shower itself: rated fixtures only. A fixture within the tub or shower footprint, up to 8 feet above the rim or threshold, must be marked for damp locations, or for wet locations where it is subject to shower spray.IRC E4003.11
- Closets: no pendants. Pendant fixtures, and fixtures with open or partly enclosed incandescent lamps, are not allowed in a clothes closet.IRC E4003.12; NEC 410.16
- Closets: keep clear of the shelves. A surface-mounted LED or incandescent fixture with a fully enclosed lamp needs 12 inches of clearance from the storage space; recessed fixtures and surface-mounted fluorescent fixtures need 6 inches.IRC E4003.12; NEC 410.16
- Outside, a floodlight camera is a light fixture too. It mounts on a weatherproof box and is wired like an outdoor light; see security camera installation.
Cost
Light fixture installation cost in 2026, by fixture type.
Published national ranges, read November 17, 2026. They are market ranges, not MDL prices. Rows marked "installed" include the fixture itself.
Scroll sideways to see the whole table.
| What | Market range | Source |
|---|---|---|
| Installing most fixtures | $75 to $125 | Home Depot |
| A light fixture job, on average | $100 to $650 | HomeGuide |
| 2026 national average, 5,281 projects | $589; most pay $159 to $1,026 | Angi |
| Labor to add a new light | $50 to $250 | HomeGuide |
| Ceiling light, installed | $70 to $250 | HomeGuide |
| Pendant light, installed | $100 to $300 | HomeGuide |
| Wall light, installed | $100 to $250 | HomeGuide |
| Track lighting, installed | $100 to $300 | HomeGuide |
| Chandelier, installed | $220 to $3,400 | HomeGuide |
| Replacing an existing chandelier | Labor $100 to $150 on a standard ceiling, $200 to $400 on a high ceiling (HomeGuide); $100 to $200 (Angi) | HomeGuide; Angi |
| Add a switch; add a dimmer | $100 to $300; $80 to $200 | HomeGuide |
| Add a ceiling junction box | $100 to $300 | HomeGuide |
Replacing an old incandescent fixture? ENERGY STAR says qualified residential LED lighting uses at least 75% less energy and lasts 25 times longer than incandescent lighting (ENERGY STAR, Light Fixtures at a Glance).
Light fixture repair
Flickering, dimming or a burning smell: when a light needs an electrician, not a new bulb.
The National Fire Protection Association tells homeowners to call a qualified electrician for any of these.
- Flickering or dimming lights.NFPA, electrical safety in the home
- Frequent blown fuses or tripping circuit breakers.NFPA
- Discolored or warm wall outlets, or sparks from an outlet.NFPA
- A burning or rubbery smell from an appliance.NFPA
- Why it matters. US fire departments responded to an estimated annual average of 46,652 home electrical fires in 2020 to 2024, with 527 deaths a year. Electrical distribution, lighting or power transfer equipment was involved in 47% of them.NFPA, home electrical fires
A light that flickers, a switch that is warm or a fixture that stopped working goes to electrical repair. For sparks, smoke or a burning smell, see emergency electrician.
Before you call
Four things that let MDL answer about your light fixture on the first call.
The job
A swap, a heavier fixture, a light where there is none, or a repair, from the table at the top of this page.
The fixture
Its type and weight, and whether its instructions call for 90°C supply wire.
The room
The ceiling height, what is above it, and whether the spot is over a tub or shower or inside a closet.
The house
The town and street, roughly when the house was built, and how the light is switched now.
Where MDL works
Light fixture work across Essex, Morris and Union County.
MDL works from 4 Harrison Avenue in West Orange. The towns below have their own MDL service-area page; from anywhere else in the three counties, call with your address and MDL will confirm coverage.
Morris County
Union County
Light fixtures
Call MDL about installing, replacing or repairing a light fixture.
Call or send the form with your town, the job from the table above, the fixture's type and weight, and the ceiling height.
Light fixture questions
Answers on cost, permits, old wiring and heavy fixtures.
Rules come from the New Jersey construction code and the model codes; prices are published national ranges, not an MDL quote.
How much does an electrician charge to install a light fixture?
Home Depot says installing most fixtures ranges from $75 to $125. HomeGuide puts the average job at $100 to $650, with labor to add a new light at $50 to $250 and the fixture extra. Angi's 2026 national average is $589 across 5,281 projects, with most people paying $159 to $1,026. These are national market ranges, not MDL prices; call 973.809.2339 for a price on your fixture.
Do you need an electrician to install a light fixture in New Jersey?
New Jersey's Uniform Construction Code says electrical work is done only by persons licensed to do it, except a single-family homeowner working on his or her own home (N.J.A.C. 5:23-2.15). Swapping a fixture for a like or similar one is ordinary maintenance with no permit. A light where there was none is new wiring and needs a permit. Older houses add a second reason: many new fixtures call for supply wire rated 90°C, and most homes wired before 1985 have 60°C wire.
Does replacing a light fixture need a permit in New Jersey?
Not for a like-for-like swap. N.J.A.C. 5:23-2.7 lists the replacement of any lighting fixture, or part of one, without an emergency battery pack, with a like or similar item as ordinary electrical maintenance, and ordinary maintenance needs no permit or notice to the town (5:23-2.14). Adding a fixture where there was none, moving one or adding a switch is new wiring and needs a permit. If you are not sure whether your job is a like-for-like swap, ask your town's building department.
What holds a light fixture to the ceiling?
An electrical box fastened to the framing. Under the National Electrical Code, a ceiling outlet box has to be able to support a fixture of up to 50 pounds; a heavier fixture needs support of its own unless the box is listed and marked inside for the weight (NEC 314.27(A)(2), the same rule as IRC E3905.6.2). In houses from the knob-and-tube era, Family Handyman notes, the old fixture may hang with no box at all, and an approved box is needed when it is replaced.
Why do the instructions for my new light fixture call for 90°C wire?
Many fixture makers require supply wire rated for at least 90°C (194°F). One maker's instruction sheet adds that most homes built before 1985 have supply wire rated to 60°C, and Family Handyman says a fixture labeled for 90°C wire cannot be safely installed in most houses wired before 1985. In Essex and Union County, about three in four homes were built before 1980 (US Census ACS 2024). Read the new fixture's instructions before buying, and have the wire in the ceiling box checked before it goes up.
Can a pendant light or chandelier hang over a bathtub?
Not within 3 feet horizontally and 8 feet vertically of the tub rim or shower threshold. The code keeps cord-connected fixtures, chain-, cable- or cord-hung fixtures, lighting track, pendants and ceiling fans with lights out of that zone. A fixture over the tub or shower itself, up to 8 feet above the rim or threshold, must be marked for damp locations, or for wet locations where shower spray can reach it (IRC E4003.11; NEC 410.10(D)).
How long does it take to install a light fixture?
Home Depot says 1 to 2 hours for a standard fixture, and up to a full day when new wiring has to run to a new location. HomeGuide puts a chandelier at 2 to 4 hours.
Sources
Where the rules, numbers and advice on this page come from.
All read November 17, 2026.
- N.J.A.C. 5:23-2, Uniform Construction Code, administration and enforcement, NJ Department of Community Affairs: ordinary maintenance (2.7), permits (2.14), licensed work (2.15), minor work (2.17A).
- UpCodes, model code text: boxes at luminaire outlets (IRC E3905.6; NEC 314.27(A)), bathtub and shower areas (IRC E4003.11; NEC 410.10(D)) and luminaires in clothes closets (IRC E4003.12; NEC 410.16).
- AFX, fixture installation instructions: the 90°C supply wire requirement and the note on homes built before 1985.
- Family Handyman, How to Hang a Ceiling Light Fixture and How to Connect Old Wiring to a New Light Fixture: 90°C fixtures in older houses, fixtures without a box.
- Housing age: US Census Bureau ACS 2024 1-year, table B25034, Essex, Morris and Union County, via Census Reporter.
- Home Depot, Light Fixture Installation: price for most fixtures, time for a standard fixture and for new wiring.
- HomeGuide, How Much Does It Cost to Install a Light Fixture? (2026) and HomeGuide, chandelier installation cost: costs by fixture type, labor, hourly rates, switches, dimmers, junction boxes, chandeliers and time.
- Angi, How Much Does It Cost to Install a Light Fixture?: 2026 national average and range, chandelier replacement labor.
- NFPA, Electrical safety in the home and Home Fires Caused by Electrical Failure or Malfunction: warning signs and 2020 to 2024 fire figures.
- ENERGY STAR, Light Fixtures at a Glance: LED energy use and life.
- Photos: Pexels, interior design of a dining room by Allyson SALNESS and modern bathroom interior with white fixtures by Peter Vang (Pexels License); Wikimedia Commons, plaster and lath ceiling opened up by Tomwsulcer (CC0). None is an MDL job.
Next steps
Related services
Recessed lighting installation
Recessed lights in a finished or open ceiling, including plaster ceilings and IC ratings.
Learn moreCeiling fan installation
Swapping a light for a fan, which needs a box rated for a fan.
Learn moreElectrical repair
Lights that flicker, switches that run warm and circuits that cut out, diagnosed before parts are replaced.
Learn moreKnob and tube wiring replacement
Old ungrounded wiring found above a ceiling fixture in a pre-1940 house.
Learn moreRequest service
Send MDL the service, town, and best callback number.
Use the form for planned service or call for urgent electrical, heating, or cooling help.