24/7 electrical, heating, and cooling help across North Jersey

Call 973.809.2339

PTAC repair · Apartments, hotels, senior housing and offices

PTAC unit repair and replacement in Essex County, NJ

Repair and replacement of packaged terminal air conditioners and PTAC heat pumps for property managers, landlords, condominium boards, hotels and offices. MDL Electric Cooling & Heating holds a New Jersey master HVACR license and an electrical contractor license. The unit and the circuit behind it are one request.

A white packaged terminal air conditioner on a plain background, its control door open above a small digital display and the louvered front grille below

The short answer

A PTAC that will not heat or cool has failed in the chassis or in the power that feeds it.

What MDL does. MDL repairs and replaces PTAC units. These are the through-the-wall heating and cooling units under the windows of apartment buildings, condominiums, hotels, senior housing, dormitories and offices. That includes PTAC heat pumps, often called PTHPs. MDL confirms the service boundary after reviewing the building and equipment.

Who this page is for. Property managers, landlords, condominium and co-op boards, hotel engineers, senior housing operators and office owners. MDL covers Essex County, from Montclair and Bloomfield to Livingston and Maplewood, and Morristown (towns).

Both trades in one request. A PTAC needs a dedicated 230/208-volt or 265-volt circuit with the right receptacle, and a working refrigeration and heating chassis. MDL holds a New Jersey master HVACR license and an electrical contractor license, so one company checks both (the electrical side).

Start here. MDL works from 4 Harrison Avenue in West Orange. Call 973.809.2339 or use the request form. Planning a replacement? The New Jersey PTAC replacement cost guide lists published prices line by line.

The nameplateModel, serial number, voltage and heater size, from the unit's label.
The plugA photo of the plug and the receptacle or sub-base it connects to.
The symptomNo heat, no cooling, no power, water on the floor or a noise, and any light pattern.
The buildingAddress, how many units are affected, access hours, and who approves the work.

What MDL checks

Seven PTAC symptoms and where each one usually leads.

The checks follow what the Amana, GE Zoneline and Friedrich manuals say about their own units. The list says where MDL looks; the diagnosis decides the repair.

Scroll sideways to see the whole table.

PTAC symptoms and checks. Manufacturer behavior from the Amana J/K series and Friedrich ZoneAire Premier manuals, read November 15, 2026.
SymptomWhat the manuals sayWhat MDL checks
No power at all230/208-volt units have an LCDI cord with a reset button; 265-volt Amana units have factory fuse holders behind the frontThe plug reset, the fuse, the breaker, the receptacle or sub-base, and the cord
Runs but will not coolBlocked or deflected airflow can make the compressor cycle on and off rapidly, which could damage it (Amana)Filter, indoor and outdoor coils, the outdoor grille, the compressor and the sealed refrigerant circuit
Runs but will not heatHeat pump models switch to electric heat at about 28°F outdoors and back at about 40°F (Friedrich)The heater element, the mode settings, the reversing valve on heat pumps, and the controls
Compressor waits to startAfter the compressor stops it will not restart for three minutes; when power returns, a two-to-four-minute random restart delay applies (Amana)Whether the delay is normal, or whether the compressor or its start parts have failed
Water inside the roomThe sleeve must be level from right to left with a slight downward pitch to the outdoor side (Amana); the four overflow slots at the rear of the sleeve must stay clear (Friedrich)Sleeve pitch, the drain kit, the overflow slots, the condensate path and the seal around the chassis
Trips the plug or breakerA damaged LCDI cord must be replaced with a new manufacturer cord and must not be repaired (Friedrich)The cord, the heater, the compressor, and whether the circuit matches the heater size
Short cycling or weak airCurtains, furniture, trees or other objects must not block the air to and from the unit (Amana)Indoor and outdoor clearances, the fan motor, the thermostat and the grille fit
An air conditioner chassis out of its case on a concrete floor, showing the black compressor, copper refrigerant tubing, the fan shroud and the condenser coil
Photo: an air conditioner chassis out of its case for cleaning, Baliuag, Bulacan, Philippines, 2020 (Judgefloro, Wikimedia Commons, CC0), cropped. A PTAC chassis slides out of its wall sleeve in a similar way. Shown for illustration, not an MDL job.
  • Test the plug once. On a 230/208-volt unit, press TEST, then RESET. Friedrich says the reset button should latch and a green light should show. If it will not reset, stop.
  • Check the filter. Amana recommends that the servicer clean the filter at the start of any troubleshooting, unless the unit is newly installed.
  • Clear the air path. Move curtains, beds and furniture away from the front grille, and note anything blocking the outdoor grille.
  • Note the lights. Amana's control board has LEDs that show board status and error codes. Write down the pattern before the power is cycled.
  • Do not improvise power. Friedrich warns against plug adapters, extension cords and removing the ground prong.

The electrical side

Every PTAC sits on its own circuit, and the heater size sets the circuit.

New Jersey's electrical subcode is the National Electrical Code 2023, with Tentative Interim Amendments 70-23-1 through 70-23-13 (N.J.A.C. 5:23-3.16(a)1). Its room air conditioner rules cover single-phase units rated 250 volts or less. UL 484 counts PTACs as room air conditioners (IAEI Magazine).

  • Cord protection is required. NEC 440.65 requires a factory-installed protection device on single-phase cord-and-plug room air conditioners. It is an LCDI, an AFCI or a heat detecting circuit interrupter, in the plug or within 12 inches of it (NFPA 70, 2023).
  • 265 volts is hard-wired. Amana does not permit a 265-volt unit on a wall socket; it is hard-wired or plugged into the receptacle in a sub-base. GE's 265-volt units are permanently connected.
  • One unit, one circuit. Friedrich requires a single circuit with a designated receptacle, protected by a time-delay fuse or an HVAC/R breaker of the listed size.
  • Voltage must stay in range. Amana lists 197 to 253 volts for a 230/208-volt unit and 238 to 292 volts for a 265-volt unit. On a 208-volt supply, the transformer connection moves to the 208-volt tap.
  • The 80 percent rule. A cord-connected room air conditioner may use up to 80 percent of a circuit it has to itself. If lights or appliances share the circuit, the limit is 50 percent (NEC 440.62, IAEI).

Scroll sideways to see the whole table.

Heater size, circuit and receptacle for 7,000 and 9,000 Btu units. Source: GE Zoneline AZ45/AZ65 architects and engineers data manual; GE notes the 4,800-watt figures drop on the low fan speed. Friedrich's ZoneAire Premier table pairs 2.5, 3.5 and 5.0 kW heaters with the same 15, 20 and 30 amp receptacles.
Power kitHeater wattsTotal ampsMinimum circuit ampacityProtective deviceReceptacle
15 amp, 230/208 V2,400 / 1,96010.5 / 9.61515 amp time-delay fuse or breakerNEMA 6-15R
20 amp, 230/208 V3,400 / 2,78014.9 / 13.62020 amp time-delay fuse or breakerNEMA 6-20R
30 amp, 230/208 V4,800 / 3,93021.0 / 19.22530 amp time-delay fuse or breakerNEMA 6-30R
15 amp, 265 V2,4009.11515 amp time-delay fuse or breakerNEMA 7-15R on the sub-base
20 amp, 265 V3,40012.92020 amp time-delay fuse or breakerNEMA 7-20R on the sub-base
30 amp, 265 V4,80018.12525 amp time-delay fuse or breakerNEMA 7-30R on the sub-base
  • The plug matches the heater. A 30 amp NEMA 6-30R receptacle and a 15 amp 6-15R are shaped differently on purpose. A cord that does not fit the outlet means the wrong kit or the wrong circuit.
  • A larger heater needs a larger circuit. Moving from a 2,400-watt to a 4,800-watt heater moves the GE kit from 15 to 30 amps. That can mean new wire and a new breaker.
  • That is regulated wiring. Altering or replacing electrical wiring is not ordinary maintenance in New Jersey and needs a permit before the work (rules).
  • A repeat trip is a fault. MDL's electrical repair page explains why, and the commercial electrician page covers the rest of the building's wiring.
A long hotel corridor with beige walls, wall sconces, red patterned carpet and wooden room doors on both sides
Photo: a hotel corridor (Manjil Aryal, WordPress Photo Directory, CC0), cropped. In a PTAC building, each door is a room with its own unit and often its own circuit. Shown for illustration, not an MDL job.

Repair or replace

Repair the part when the sealed system is sound; compare a replacement when it is not.

Age alone does not decide it. The failed part, the sleeve and the circuit do. When the answer is replacement, the PTAC replacement cost guide shows what each line of a New Jersey quote usually covers.

Repair usually makes sense when

  • The fault is a fan motor, control board, heater, thermostat or cord
  • The sealed refrigerant system holds its charge
  • Parts for the model are still available
  • The sleeve and outdoor grille are sound

Compare a replacement when

  • The compressor or the sealed system has failed
  • The sleeve is corroded or no longer seals
  • Several units in the building fail in one season
  • Parts for the model are no longer made

What a replacement must match

  • The voltage and receptacle at the sleeve
  • A heater size the circuit can carry
  • The 42 by 16 inch sleeve, or an adapter kit
  • A grille the manufacturer approves
  • The sleeve. GE says its replacement units fit existing 42-inch-wide by 16-inch-high sleeves. Friedrich requires a sleeve no deeper than 13 3/4 inches without a baffle kit. It uses an adapter kit to put a P-series chassis in a T-series sleeve.
  • The grille. Amana says to check before putting a new chassis behind an existing or specialized grille. An improper grille can cut capacity, raise energy use, shorten compressor life and possibly void the warranty.
  • The refrigerant. The Amana J/K series and Friedrich ZoneAire Premier units in these manuals use R-32. Friedrich labels it a flammable refrigerant: repairs by trained personnel only, with A2L-approved service equipment.
  • The first days. Amana says rated performance is reached after 72 hours of operation, so judge a new unit after three days, not three minutes.

Buildings with many units

Apartment buildings, hotels and senior housing carry rules and schedules a house does not.

One failed PTAC is one cold room. Twenty failed PTACs is a building problem. Send the unit count and the model numbers, and MDL scopes the work after reviewing the building.

  • Apartment buildings. New Jersey's heat season runs from October 1 to May 15. Each unit in a building of three or more apartments must reach 68°F from 6:00 A.M. to 11:00 P.M. and 65°F overnight (N.J.A.C. 5:10-14.4 and 2.2).
  • Who pays for the heat. The owner supplies the heat unless a tenant agreed in writing to heat a unit with its own separately billed heating equipment (N.J.A.C. 5:10-14.4(c)). The written agreement decides it.
  • Hotels. Amana's energy management can set back temperatures in unrented or unoccupied rooms, using door switch and motion sensor inputs.
  • Vacant rooms in winter. Friedrich's freeze protection turns on the fan and electric heat below 40°F and warms the room to 50°F, if the feature is left on.
  • Access. List the rooms, the hours they can be entered, and who holds the keys, so a visit covers every affected unit.

New Jersey rules

When PTAC work needs a permit, a notice or nothing at all.

Read November 15, 2026 from the Uniform Construction Code, N.J.A.C. 5:23-2 (published through August 17, 2026), NJ Department of Community Affairs. The code does not name PTACs. Your town's construction office applies it to a specific job.

Scroll sideways to see the whole table.

New Jersey permit rules that apply to PTAC work. Sources: N.J.A.C. 5:23-2.7, 2.14, 2.15 and 2.17A and 5:23-3.16.
JobWhat the rule saysSection
Repair a unit"Repair of air conditioning equipment and systems" is ordinary maintenance: no permit, inspection or notice.5:23-2.7(c)5.iv
Replace controlsRepair or replacement of control devices for heating and air conditioning equipment is ordinary maintenance.5:23-2.7(c)5.v
Replace a receptacleReplacing a receptacle with a like or similar item is ordinary electrical maintenance, outside hazardous locations.5:23-2.7(c)3.i
Replace the unitReplacing existing air conditioning units with new appliances of like capacity is minor work: notice before work begins, then a permit application within five business days.5:23-2.17A(a), (b), (c)3
Minor work inspectionThe enforcing agency inspects within three business days of the request, or another time within 30 days that both sides agree.5:23-2.17A(d)1
New or altered wiringAltering or replacing electrical wiring is not ordinary maintenance; regulated work needs an application and a permit first.5:23-2.7(b)6.iii; 2.14(a)
Who may do itElectrical and HVACR work only by persons licensed for it, except a single-family homeowner on his or her own dwelling.5:23-2.15(b)2.i
Electrical codeThe National Electrical Code 2023, with Tentative Interim Amendments 70-23-1 through 70-23-13, is New Jersey's electrical subcode.5:23-3.16(a)1

What to send

Six details that let MDL scope a PTAC repair.

Safe photos and a plain description are enough to start. Do not open the electrical box, remove the chassis or bypass the plug to collect them.

01

The building

Address and ZIP code, building type, and how many apartments, rooms or offices have PTACs.

02

The nameplate

A photo of the label: model, serial number, voltage, and heater size in kW or amps.

03

The power

A photo of the plug and the receptacle or sub-base, and whether a breaker or the plug has tripped.

04

The symptom

No heat, no cooling, no power, water, noise or short cycling, and any light pattern on the controls.

05

How many units

One unit, several, or a whole floor, and the model numbers if they differ.

06

Access and approval

Who can open the rooms, the hours they can be entered, and who approves the work.

Where MDL works

PTAC repair across Essex County and in Morristown, from a West Orange base.

MDL works from 4 Harrison Avenue in West Orange. These towns have their own MDL service-area page. MDL also covers the Caldwells and Millburn through the Essex County page. Include the exact address and ZIP code so coverage can be confirmed for the building.

PTAC repair

PTACs down in an apartment building, a hotel or an office? Call MDL.

Call or send the form with the address, the number of units affected, a nameplate photo and the symptom. The form opens with Commercial Heating / HVAC chosen.

PTAC questions

Straight answers on heat, cooling, power, permits and what to send.

Manufacturer behavior comes from the Amana, GE and Friedrich manuals, and rules from the New Jersey texts named on this page. MDL publishes no prices, and this page lists none.

What does PTAC repair and replacement cover?

MDL repairs and replaces PTAC units, meaning packaged terminal air conditioners and PTAC heat pumps. These are the through-the-wall units in apartment buildings, condominiums, hotels, senior housing, dormitories and offices. The work covers the chassis: compressor, coils, fans, heater and controls. It also covers the power that feeds it: the circuit, the receptacle or sub-base, and the cord. MDL confirms the service boundary after reviewing the building and equipment.

Why is my PTAC not heating?

Start with power and mode. A 230/208-volt unit has a leakage current detection (LCDI) cord with a reset button. Amana tells owners to check it if the unit does not run. After the compressor stops, an Amana unit will not restart it for three minutes. Friedrich's heat pump models switch to electric heat at about 28°F outdoors. So a failed heater shows up as cold air on cold days. MDL checks the heater, the controls and the circuit.

Why is my PTAC not cooling?

The common causes are airflow and the sealed refrigerant system. Amana warns that blocked or deflected airflow can make the compressor cycle on and off rapidly, which could damage it. A dirty filter or coil cuts cooling too. If the filter, coils and grille are clear and the compressor runs without cooling, the problem is usually in the refrigerant circuit. MDL then decides whether a repair or a replacement chassis makes more sense.

My PTAC trips its plug or the breaker. What does that mean?

An LCDI plug that trips again after a reset is reporting a fault. Friedrich says a cord that fails its test or is damaged must not be repaired. It must be replaced with a new cord from the manufacturer. A breaker that trips can mean a shorted heater or compressor, or a circuit smaller than the heater needs. Do not keep resetting either one; MDL traces it on both sides of the wall.

What is the difference between a 230/208-volt and a 265-volt PTAC?

A 230/208-volt PTAC plugs into a dedicated 250-volt receptacle through an LCDI cord. The receptacle is a NEMA 6-15R, 6-20R or 6-30R, depending on the heater. A 265-volt PTAC cannot be plugged into a wall outlet. Amana requires it to be hard-wired or plugged into the receptacle in its sub-base. GE uses NEMA 7-15R, 7-20R and 7-30R receptacles on 265-volt sub-bases. A replacement has to match the voltage the building supplies to that sleeve.

Should I repair or replace a PTAC?

Repair usually makes sense when the failed part is outside the sealed refrigerant system and parts are available. Typical examples are a fan motor, control board, heater, thermostat or cord. A replacement comparison makes sense when the compressor or sealed system has failed, the sleeve is corroded, or several units in the building are failing. MDL's PTAC replacement cost guide lists published equipment and installation figures for New Jersey owners.

Does PTAC repair or replacement need a permit in New Jersey?

Repairing air conditioning equipment is ordinary maintenance under N.J.A.C. 5:23-2.7(c)5.iv: no permit, inspection or notice. Replacing an existing air conditioning unit with a new appliance of like capacity is minor work under N.J.A.C. 5:23-2.17A(c)3: notice to the construction office before work begins, a permit application within five business days, and an inspection. New or altered wiring needs a permit first (N.J.A.C. 5:23-2.14(a)). The code does not name PTACs, so the local construction office confirms how it treats a specific job.

Who has to keep the heat on in an apartment building heated by PTACs?

New Jersey's heat season runs from October 1 to May 15. In a building with three or more apartments, every unit must reach 68°F from 6:00 A.M. to 11:00 P.M. and 65°F overnight (N.J.A.C. 5:10-14.4 and 5:10-2.2). The owner supplies the heat and keeps the system working. The exception is a tenant who agreed in writing to heat a unit with its own separately billed heating equipment (N.J.A.C. 5:10-14.4(c)).

What should I send with a PTAC repair request?

Send the building address and type, and how many units are affected. Add a photo of the nameplate showing the model, serial number, voltage and heater size. Add a photo of the plug and the receptacle or sub-base. Describe the symptom and any light pattern on the controls. Say whether the unit is a heat pump or has electric heat only. Name who can open the rooms and approve the work.

How much does PTAC repair or replacement cost?

MDL does not publish prices, and this page lists none. The cost depends on what failed and on the unit's voltage and heater size. Whether the sleeve and grille can be reused, access, and the number of units matter too. MDL's PTAC replacement cost guide collects published equipment and installation figures, New Jersey sales tax and the PSE&G incentive for qualifying units.

Which towns does MDL cover for PTAC repair?

MDL works from 4 Harrison Avenue in West Orange. It covers Essex County towns including West Orange, Montclair, Bloomfield, Glen Ridge, Verona, Cedar Grove, Nutley and Belleville. It also covers Livingston, Maplewood, South Orange, Millburn and Short Hills, the Caldwells, and Morristown. Send the exact address and ZIP code so coverage can be confirmed for the building.

Sources

Where the facts on this page come from.

All read November 15, 2026.

Next steps

Related services

PTAC

PTAC replacement cost in New Jersey

Published equipment and installation figures, sales tax, permits and the PSE&G incentive.

Learn more
Commercial

Commercial HVAC service

Heating, cooling and boiler service for a business or managed property.

Learn more
Commercial

Commercial electrician

Troubleshooting, circuits and panels for the rest of the building.

Learn more
Commercial

Commercial services hub

Electrical and HVAC requests for the same building in one place.

Learn more

Request service

Send MDL the service, town, and best callback number.

Use the form for planned service or call for urgent electrical, heating, or cooling help.