24/7 electrical, heating, and cooling help across North Jersey

Call 973.809.2339

2026 PTAC cost guide · New Jersey · apartments, hotels and offices

PTAC replacement cost in New Jersey, 2026: unit prices, installation and the PSE&G rebate

Short answer: On November 15, 2026, one national distributor listed replacement PTAC heat pumps at $699 to $1,425 each, before tax and installation. New York City firms publish $500 to $800 to install a unit, and $900 to $1,400 for a swap into an existing sleeve. A new wall opening runs $2,500 to $3,500 or more. New Jersey adds 6.625% sales or use tax on the equipment. PSE&G pays its business customers $175 a ton for a qualifying PTAC and $300 a ton for a heat pump model. What moves a New Jersey quote most is the voltage, the heater size, the sleeve and the circuit.

Published November 15, 2026 Sources read November 15, 2026 Every figure sourced
The outdoor end of an older through-the-wall air conditioner set in a textured wall, rust along the top of its metal cabinet and a dusty mesh grille
Photo: Mark Wagner (Carnildo) on Wikimedia Commons, public domain, cropped. The outdoor end of an older through-the-wall air conditioner in the United States, 2005, with rust along its cabinet. Corrosion like this is one reason a sleeve gets priced into a replacement. Not a PTAC, and not an MDL job.

The unit is the easy line. The sleeve, the voltage and the circuit decide the rest.

Most pages that rank for this search in New Jersey belong to New York City contractors (Google results read from West Orange, November 15, 2026). Their prices are real, but they describe Manhattan and Queens buildings. This guide uses the same published figures and adds what a New Jersey owner also needs. That means the state's tax and permit rules, PSE&G's incentive, and the electrical lines a replacement can trigger.

Start with what failed. A fan motor, a control board or a cord is usually a repair. A failed compressor or a rusted sleeve is usually a replacement comparison. MDL's PTAC repair and replacement page covers the diagnosis.

Replacement unit$699 to $1,425

PTAC heat pumps from 7,000 to 15,000 Btu at HVACDirect, sale listings read November 15, 2026. Brands listed include ACiQ, Friedrich, Amana and GE.

Installed, published$900 to $3,500

Lion Enterprises, New York County: $900 to $1,400 for a swap into an existing sleeve, and $2,500 to $3,500 or more for a new opening.

New Jersey tax6.625%

Sales tax, or use tax on equipment bought online and delivered to New Jersey. On a $1,474 unit, sleeve and grille, that is $97.65.

PSE&G incentive$175 or $300 a ton

For business customers, on units that meet PSE&G's efficiency table. A 9,000 Btu heat pump is three-quarters of a ton: $225.

MDL verdict

Price the replacement as separate lines, not one number. Match the voltage and heater to the circuit already in the wall. Reuse the sleeve only when it is sound and the new chassis is built for it. Check PSE&G eligibility before the units are ordered, not after.

Replacement PTAC heat pumps listed at $699 to $1,425 on November 15, 2026.

HVACDirect, a national online distributor, lists PTACs by size, heater and voltage. The prices below were its sale prices on November 15, 2026, during a pre-Black Friday promotion. Its listed "was" prices were higher. Prices change often, so treat these as a snapshot of the market.

Replacement PTAC heat pump prices at HVACDirect, read November 15, 2026 (sale prices; equipment only, before tax, shipping and installation)
Unit as listed Capacity Electric heater Voltage Listed price
ACiQ PTAC heat pump7,000 Btu2.5 kW208/230 V$699
ACiQ PTAC heat pump9,000 Btu3.5 kW208/230 V$749
ACiQ PTAC heat pump15,000 Btu5 kW208/230 V$869
Friedrich ZoneAire Select heat pump9,000 Btu3.5 kW265 V$1,154
Friedrich ZoneAire Premier heat pump9,000 BtuPer model208/230 V$1,249
Amana PTAC heat pump7,000 Btu2.5 kWPer model$1,319
Amana PTAC heat pump15,000 Btu3.5 kWPer model$1,399
GE Zoneline heat pump15,000 BtuPer model208/230 V$1,425

PTAC Units NYC publishes its own 2026 ranges for New York City buyers. They run a little higher than the online listings:

  • By heating type. Cooling with electric heat $900 to $1,500. Heat pump models $1,300 to $2,200. Cooling with hydronic heat $1,200 to $1,900.
  • By size. 7,000 Btu $900 to $1,300. 9,000 Btu $1,000 to $1,500. 12,000 Btu $1,200 to $1,900. 15,000 Btu $1,400 to $2,300.
  • High-efficiency or smart-controlled units. $1,800 to $2,500 or more.
  • What it says changes the price. Capacity, brand, heating type, efficiency, the sleeve and grille, the electrical connection and the controls.

Naming a brand here is market evidence, not a recommendation. It does not mean MDL sells, stocks or is certified for that brand. The right unit is the one that fits the sleeve, the voltage and the circuit already in the wall.

A replacement quote is five to eight lines, and only one of them is the chassis.

The published installation figures we found come from New York City firms. PTAC Units NYC puts professional installation at $500 to $800 per unit. Lion Enterprises puts a swap into an existing sleeve at $900 to $1,400 in New York County. It prices a PTAC where none existed at $2,500 to $3,500 or more.

The lines in a PTAC replacement quote, with the published figure for each where one exists (read November 15, 2026)
Line When it applies Published figure Source
ChassisEvery replacement$699 to $1,425HVACDirect sale listings
Installation laborEvery replacement$500 to $800 per unitPTAC Units NYC
Wall sleeveSleeve corroded, damaged or the wrong size$150 sleeve; $150 to $400 to replace oneHVACDirect; PTAC Units NYC
Outdoor grilleGrille damaged or not approved for the new chassis$75 stamped aluminum; $115 architecturalHVACDirect
Cord kit or sub-baseHeater size or voltage changes, or a 265 V unitVaries by modelGE, Amana manuals
New or larger circuitThe new heater needs more amps than the circuit carries$570 to $1,000 national; $890 to $1,090 in New YorkAngi, October 30, 2026
Permit and inspectionUnit replacement is minor work; wiring changes need a permitTown fee schedule; $100 to $400 for inspections, nationalN.J.A.C. 5:23-2; Angi
TaxEquipment and taxable parts6.625%NJ Division of Taxation

PTAC Units NYC also gives a worked example. A small hotel replaces 20 units with 9,000 Btu heat pump models. At about $1,400 a unit plus $400 to install, it reaches $1,800 a room and about $36,000 in total. Its $400 installation figure sits below its own $500 to $800 range. Budget from the range, not the example.

Four things push a job toward the top of these ranges:

  1. A new opening. Cutting the wall, setting a sleeve and running a circuit is Lion's $2,500 to $3,500 case.
  2. A heater change. A bigger heater can need a bigger circuit and receptacle (section 06).
  3. A sleeve that will not take the new chassis. Depth, size and series limits are in section 07.
  4. Access. Lion and PTAC Units NYC both name upper floors, elevators and building rules as cost factors.

The failed part decides it before the age of the unit does.

Lion Enterprises publishes a rule of thumb. Repair when the job costs under 30% of a new unit and it is the first problem. Replace when the repair reaches 50% or more of a new unit. It adds age: under seven years favors repair, and over ten favors replacement. It also says most PTACs last 10 to 15 years with regular maintenance.

The sealed system is sound

Usually a repair

  • A fan motor, a control board, a thermostat or a heater element
  • A damaged LCDI cord; Friedrich says it must be replaced with a new manufacturer cord, never repaired
  • A clogged filter, a dirty coil or a blocked grille
  • A drain or sleeve pitch problem that leaks water into the room
The core of the unit has failed

Usually a replacement comparison

  • A failed compressor; Lion calls it the most expensive part in the unit
  • A leak in the sealed refrigerant system
  • A corroded sleeve that no longer seals or drains
  • Several units failing in the same season

A rule of thumb needs a diagnosis behind it. MDL checks the chassis and the power that feeds it, then prices the repair against a replacement. See the PTAC repair page for the symptoms MDL checks and what to send.

In a New Jersey winter, the heat source matters more than the price tag.

A PTAC with electric heat warms the room with a resistance heater. A PTAC heat pump moves heat from outdoors and uses its heater only when it must. Friedrich's heat pump models switch to the electric heater at about 28°F outdoors and back at about 40°F.

The table prices the same heat both ways at New Jersey's August 2026 electricity prices. It uses GE's 3,400-watt heater, which GE rates at 11,600 Btu an hour. The heat pump is set at 3.19 COP. That is the lowest PSE&G accepts for a standard-size heat pump of 9,000 to 10,000 Btu.

Running cost for 11,600 Btu an hour of heat at New Jersey's August 2026 prices (EIA Table 5.6.A, preliminary; our arithmetic)
Heat source Power drawn Per hour, commercial (18.71¢) Per 100 hours, commercial Per hour, residential (24.61¢) Per 100 hours, residential
Electric heater, 3,400 W3.40 kW$0.64$63.61$0.84$83.67
Heat pump at 3.19 COP1.07 kW$0.20$19.94$0.26$26.23
  • The rate depends on the meter. A building on a commercial account pays the commercial rate. A unit on a tenant's meter pays the residential rate.
  • COP falls as it gets colder. The 3.19 figure is a rating, not a January night. Below about 28°F, Friedrich's units run on the heater anyway.
  • The incentive follows the heat pump. PSE&G pays $300 a ton for a qualifying heat pump and $175 for a qualifying PTAC (section 09).
  • Who pays matters. In a building of three or more apartments, the owner supplies the heat. The exception is a tenant who agreed in writing to heat a separately billed unit (N.J.A.C. 5:10-14.4(c)).

The replacement has to match the voltage and receptacle already in the wall.

PTACs come in two common voltage families. A 230/208-volt unit plugs into a dedicated receptacle through a cord kit. A 265-volt unit is never plugged into a wall outlet. Amana requires it to be hard-wired or plugged into the receptacle in its sub-base.

GE Zoneline 7,000 and 9,000 Btu units: heater, circuit and receptacle (GE architects and engineers data manual; GE notes the 4,800-watt figures drop on the low fan speed)
Power kit Heater watts Minimum circuit ampacity Protective device Receptacle
15 amp, 230/208 V2,400 / 1,9601515 amp time-delay fuse or breakerNEMA 6-15R
20 amp, 230/208 V3,400 / 2,7802020 amp time-delay fuse or breakerNEMA 6-20R
30 amp, 230/208 V4,800 / 3,9302530 amp time-delay fuse or breakerNEMA 6-30R
15, 20 or 30 amp, 265 V2,400, 3,400 or 4,80015, 20 or 2515, 20 or 25 amp time-delay fuse or breakerNEMA 7-15R, 7-20R or 7-30R on the sub-base
  • Same heater, same circuit: no electrical line. A like-for-like heater on a matching receptacle is the cheap case.
  • Bigger heater: maybe a new circuit. Moving from 2,400 to 4,800 watts moves GE's kit from 15 to 30 amps. That can mean new wire, a new breaker and a new receptacle.
  • Cord protection is required. NEC 440.65 requires a factory-installed LCDI, AFCI or heat detecting interrupter on single-phase cord-connected room air conditioners. UL 484 counts PTACs as room air conditioners (IAEI). GE's line cord kits have carried LCDI protection since August 1, 2004.
  • Watch the 208-volt buildings. On a 208-volt supply the heater puts out less heat; GE's 3,400-watt heater makes 2,780 watts. Amana moves the transformer connection to the 208-volt tap.
  • The 80 percent rule. A cord-connected room air conditioner may not exceed 80% of a circuit it has to itself (NEC 440.62, IAEI).

New Jersey enforces the National Electrical Code 2023 (N.J.A.C. 5:23-3.16). Altering or replacing wiring needs a permit before the work (N.J.A.C. 5:23-2.7(b)6.iii and 2.14(a)). MDL holds an electrical contractor license as well as a master HVACR license, so the circuit and the unit are one job.

Reusing the sleeve saves the most, when the new chassis is built for it.

Many PTACs share one opening size. GE says it has kept the same sleeve dimensions since 1961: 42 inches wide, 16 high and 13 3/4 deep. That shared size is why a swap can stay near Lion's $900 to $1,400.

  • Depth. Friedrich requires a 16-by-42-inch sleeve no deeper than 13 3/4 inches. A deeper sleeve needs a baffle kit.
  • Series. Friedrich uses an adapter kit to put a P-series chassis in a T-series sleeve.
  • Grille. Amana says to check before putting a new chassis behind an existing or specialized grille. An improper grille can cut capacity, raise energy use, shorten compressor life and possibly void the warranty.
  • Condition. A sleeve must drain to the outdoors. Amana wants it level side to side, with a slight downward pitch outward. A rusted or bent sleeve is a line on the quote.
  • Price. HVACDirect listed a standard 42-inch sleeve at $150 and grilles at $75 to $115. PTAC Units NYC adds $150 to $400 to replace a damaged sleeve.
An older through-the-wall room air conditioner with a brown wood-grain front panel and louvered top vents, set in a wooden wall frame
Photo: Mark Wagner (Carnildo) on Wikimedia Commons, public domain, cropped, maker's badge blurred. An older through-the-wall room air conditioner, 2005. Not every unit in a wall is a PTAC. Replacing a unit like this with a PTAC usually means a new 42-by-16-inch opening, which is Lion's $2,500-and-up case. Not an MDL job.

A like-capacity replacement is minor work in New Jersey. A repair needs no permit.

New Jersey's Uniform Construction Code does not name PTACs. It does name air conditioning units, and a town's construction office applies it to a given job.

  • Repair. "Repair of air conditioning equipment and systems" is ordinary maintenance: no permit, inspection or notice (N.J.A.C. 5:23-2.7(c)5.iv).
  • Like-capacity replacement. Replacing an existing air conditioning unit with a new one of like capacity is minor work. The owner or contractor gives notice before work starts and applies for the permit within five business days (5:23-2.17A(b) and (c)3).
  • Inspection. The town inspects minor work within three business days of the request, or another time within 30 days that both sides agree (5:23-2.17A(d)1).
  • Wiring. A new or altered circuit is not ordinary maintenance and needs a permit before the work (5:23-2.7(b)6.iii; 2.14(a)).
  • Licensed work. Electrical and HVACR work only by persons licensed for it, except a single-family homeowner on his or her own dwelling (5:23-2.15(b)2.i).

New Jersey's sales tax rate is 6.625%, on most tangible goods and certain services (NJ Division of Taxation, updated November 13, 2026). Equipment bought online and delivered to a New Jersey address owes 6.625% use tax if the seller does not collect sales tax. Use tax is figured on the price including shipping (Tax Topic Bulletin S&U-4). How tax applies to installation labor depends on the job, so ask for tax as its own line.

  • One unit, sleeve and grille. $1,249 + $150 + $75 = $1,474; tax at 6.625% is $97.65.
  • The lowest listing. A $699 unit carries $46.31 in tax.
  • Twenty units. Twenty $1,249 units are $24,980 before tax, and $1,654.93 in tax.

PSE&G pays $175 a ton for a qualifying PTAC and $300 a ton for a heat pump.

PSE&G's Prescriptive Program gives business customers incentives for efficient replacement equipment. Its 2026 commercial and industrial incentive table lists packaged terminal units by size and efficiency. Each unit must meet or exceed the ASHRAE 90.1-2019 efficiency listed for its size.

PSE&G prescriptive incentive per unit, 2026 rates (our arithmetic, assuming tons are cooling Btu divided by 12,000; confirm with PSE&G)
Unit size Tons PTAC at $175 a ton PTAC heat pump at $300 a ton
7,000 Btu0.58$102.08$175.00
9,000 Btu0.75$131.25$225.00
12,000 Btu1.00$175.00$300.00
15,000 Btu1.25$218.75$375.00
  1. Check the efficiency first. For a standard-size heat pump of 9,000 to under 10,000 Btu, PSE&G's table asks for 11.01 EER and 3.19 COP.
  2. Keep the paperwork. PSE&G requires an AHRI certificate and the manufacturer's specification sheet for new electric HVAC units.
  3. Use your own contractor if you like. PSE&G says customers may use a preferred contractor that meets eligibility requirements and still receive rebates.
  4. Mind the 90 days. A facility that finished an efficiency upgrade within the last 90 days may still be eligible, PSE&G says.
  5. Ask about on-bill repayment. Qualifying equipment can also get interest-free, on-bill repayment for the cost the incentive does not cover.

Twenty qualifying 9,000 Btu heat pumps would come to $4,500 at these rates. The program is for PSE&G business customers, so confirm the account and the building qualify before counting it. This guide does not claim that MDL is a PSE&G program partner.

A mini-split costs more per room, and it does not fit in a PTAC sleeve.

If you are weighing a ductless mini-split instead, the published prices differ. HomeGuide puts a single-zone mini-split at $2,500 to $6,000 installed, and a wall-mounted unit at $2,500 to $5,000 per zone (October 8, 2025). That compares with Lion's $900 to $1,400 for a PTAC swap.

  • The opening. A mini-split needs a line-set hole and an outdoor unit. The old 42-by-16-inch sleeve has to be closed off.
  • The incentive. PSE&G lists ductless mini-split heat pumps at $250 a ton at 12.4 EER2, against $300 a ton for a qualifying PTAC heat pump.
  • The room. A PTAC heats and cools one room from one wall. HomeGuide notes that each extra indoor unit adds equipment and labor cost.
The outdoor unit of a split heat pump on wall brackets beside a brick house, its round fan grille facing forward and a window behind it
Photo: uploaded by Ppntori to Wikimedia Commons in 2006, public domain, cropped, maker's logo blurred. The outdoor unit of a split heat pump on a brick house. A mini-split needs a unit like this outside plus refrigerant lines through the wall; a PTAC carries both halves in one chassis. Not an MDL job.

Ask for each line in writing before the units are ordered.

  1. What failed in each unit, and why repair or replacement was chosen.
  2. The replacement model, its capacity, heater size and voltage, and its AHRI certificate.
  3. Whether the existing sleeve and grille stay, with the reason.
  4. The cord kit or sub-base, and whether the circuit and receptacle change.
  5. The permit path: minor work notice, wiring permit, or none.
  6. Removal of the old chassis, and who handles it.
  7. Tax as its own line, and the PSE&G incentive as its own line.
  8. Access: which rooms, which hours, and who lets the crew in.

Lines 1, 3 and 4 are the work on MDL's PTAC repair and replacement page: the diagnosis, the unit and the circuit behind it. MDL publishes no prices, and no figure in this guide is an MDL price.

Have PTACs failing in an Essex County building?

Send MDL the address, the number of units affected, a nameplate photo, a photo of the plug and receptacle, and the symptom. The request form is on MDL's PTAC repair page.

PTAC replacement cost questions from New Jersey owners and managers.

How much does it cost to replace a PTAC unit in New Jersey?

The unit itself listed at $699 to $1,425 for a PTAC heat pump at HVACDirect on November 15, 2026. New York City firms publish $500 to $800 to install it, and $900 to $1,400 for a swap into an existing sleeve. A new opening runs $2,500 to $3,500 or more. New Jersey adds 6.625% tax on the equipment. A new circuit, sleeve or grille adds its own line.

How much does a PTAC unit cost?

At one distributor on November 15, 2026, PTAC heat pumps from 7,000 to 15,000 Btu listed at $699 to $1,425 on sale. PTAC Units NYC publishes $900 to $2,500 for the equipment, and $1,300 to $2,200 for heat pump models.

Is it worth repairing a PTAC?

Usually, when the fault is a fan motor, board, heater, thermostat or cord and the sealed system is sound. Lion Enterprises suggests repair under 30% of a new unit's price on a first problem, and replacement at 50% or more. A failed compressor usually points to replacement.

Can I reuse the wall sleeve?

Often. GE says its sleeve dimensions have not changed since 1961, which makes replacing older units easier. Friedrich limits sleeve depth to 13 3/4 inches without a baffle kit and uses an adapter kit between its P and T series. A rusted or bent sleeve should be replaced; PTAC Units NYC puts that at $150 to $400.

Do I need a permit to replace a PTAC in NJ?

Replacing an air conditioning unit with one of like capacity is minor work under N.J.A.C. 5:23-2.17A(c)3: notice before work, a permit application within five business days, and an inspection. A repair is ordinary maintenance with no permit. New or altered wiring needs a permit first. Your town's construction office applies the rule to the job.

Does PSE&G give a rebate for PTAC units?

For business customers, yes, if the unit qualifies. PSE&G pays $175 a ton for a PTAC and $300 a ton for a PTAC heat pump. Each unit must meet the ASHRAE 90.1-2019 efficiency for its size. PSE&G requires an AHRI certificate and the specification sheet. A 9,000 Btu heat pump works out to $225, assuming tons are Btu divided by 12,000.

Is a 265-volt PTAC more expensive?

Not necessarily. On November 15, 2026, Friedrich's 9,000 Btu ZoneAire Select heat pump listed at $1,154 in 265 volts, inside the range of the 230/208-volt listings. The difference is in the connection. A 265-volt unit is hard-wired or plugged into a sub-base receptacle, never a wall outlet. The replacement must match what the building has.

How long do PTAC units last?

Lion Enterprises says most last 10 to 15 years with regular maintenance. The manuals stress the upkeep that gets there: a clean filter, a clear outdoor grille, and a sleeve that drains to the outside.

Who wrote it, and what it is not.

MDL Electric Cooling & Heating wrote this guide. MDL works from 4 Harrison Ave, West Orange, and holds a New Jersey master HVACR contractor license (#19HC00308200) and an electrical contractor license (#34EI01606200). The guide collects published prices, rules and rates for PTAC replacement in New Jersey. No figure here is an MDL price, and MDL publishes none. Every figure was read from the sources below on November 15, 2026. The per-unit incentive, tax and running-cost figures are our arithmetic on those sources, shown so you can check them.

Sources, read November 15, 2026

Prices, rates and codes change. Where a source's own figures disagree, both are shown. Nothing here is an MDL price. No company named here was asked or paid to appear; their prices are quoted as market evidence only.

  1. HVACDirect — PTAC unitsSale prices on November 15, 2026: ACiQ 7,000, 9,000 and 15,000 Btu heat pumps $699, $749, $869; Friedrich ZoneAire Select 9,000 Btu 265 V $1,154; Friedrich ZoneAire Premier 9,000 Btu $1,249; Amana 7,000 and 15,000 Btu $1,319 and $1,399; GE Zoneline 15,000 Btu $1,425; ACiQ 42-inch sleeve $150; grilles $75 and $115.
  2. PTAC Units NYC — How much is a PTAC unit? 2026-2027 pricesEquipment $900 to $2,500; installation $500 to $800; prices by type and size; sleeve replacement $150 to $400; 20-room example about $36,000.
  3. Lion Enterprises — PTAC unit installation costs and decisionsJuly 2, 2026: $900 to $3,500 per unit in New York County; $900 to $1,400 swap; $2,500 to $3,500 or more for a new opening; 30% and 50% repair rule; 10 to 15 year life; compressor failure.
  4. Lion Enterprises — Avoid a costly breakdown with timely PTAC repair in QueensJanuary 2, 2026: the 30% and 50% rule of thumb.
  5. Angi — Cost to install a dedicated circuitBarbara Bellesi Zito, updated October 30, 2026: $570 to $1,000, $700 average; New York $890 to $1,090; inspections $100 to $400.
  6. HomeGuide — Ductless mini split AC costTamatha Hazen, October 8, 2025: single-zone $2,500 to $6,000 installed; wall-mounted $2,500 to $5,000 per zone.
  7. PSE&G — Prescriptive ProgramBusiness customer incentives; preferred contractor if eligible; 90-day look-back; interest-free on-bill repayment for qualifying equipment.
  8. PSE&G — Incentive rates and requirements, 2026 commercial and industrial programs (PDF)PTAC $175 a ton; PTHP $300 a ton; ductless mini-split heat pumps $250 a ton; ASHRAE 90.1-2019 qualifying efficiency; AHRI certificate and specification sheet.
  9. NJ Division of Taxation — Sales and use tax6.625% rate; page last updated November 13, 2026.
  10. NJ Division of Taxation — Tax Topic Bulletin S&U-4 (PDF)Rev. 07/22: use tax on online purchases delivered to New Jersey, including shipping, at 6.625%.
  11. US EIA — Electric Power Monthly, Table 5.6.AAugust 2026, New Jersey: residential 24.61¢, commercial 18.71¢ a kWh; released October 23, 2026; 2026 values preliminary.
  12. GE Zoneline AZ45/AZ65 architects and engineers data manual (PDF)Heater watts and Btu, circuit ampacity, protective devices, NEMA receptacles, LCDI line cord kits since August 1, 2004, the same sleeve dimensions since 1961.
  13. Amana J/K series PTAC installation instructions and owner's manual (PDF)265-volt connection, 208-volt tap, sleeve level and pitch, grille warning.
  14. Friedrich ZoneAire Premier R-32 series PTAC installation and operation manual (PDF)94141010_04, 10/2026: 28°F and 40°F heat pump changeover, sleeve depth, adapter kit, LCDI cord replacement.
  15. IAEI Magazine — Air-conditioning equipment installationsKeith Lofland, July/August 2017: NEC 440.62 and 440.65; UL 484 covers PTACs.
  16. UpCodes — NFPA 70 (2023), section 440.65The three factory-installed protection devices for cord-connected room air conditioners.
  17. N.J.A.C. 5:23-2 — Uniform Construction Code, administration (PDF)Published through August 17, 2026: 2.7 ordinary maintenance, 2.14 permits, 2.15 licensed work, 2.17A minor work.
  18. N.J.A.C. 5:23-3 — Subcodes (PDF)5:23-3.16 adopts the National Electrical Code 2023.
  19. N.J.A.C. 5:10 — Maintenance of hotels and multiple dwellings (PDF)14.4(c): the owner supplies heat unless a tenant agrees in writing to heat a separately billed unit.
  20. Photos: Wikimedia Commons, Single-room AC unit, external and Single-room AC unit, internal (Mark Wagner, 2005, public domain); Outunit of heat pump (Ppntori, uploaded 2006, public domain). Cropped; logos blurred. Not MDL jobs.